A New Holland Baler Knotter is a mechanical tool used to tie twine around a hay bale. It works by pulling the twine tightly around the bale and tying it at the end.
The knotter is part of a mechanical baler and has several parts: a needle for pulling the twine and a long arm that pushes the twine around the bale. The mechanism ties the knot by pulling the twine through the twine. It also produces single and multiple knots.
A baler knotter is one of the most important components of the baler. This component moves twine between the knots, which is necessary to secure the bales. The twine holder holds the twine between the knots while the knife arm cuts the twine.
While using a New Holland baler, you’ve probably encountered some troubleshooting issues while operating a knotter. If so, this article will show you how to troubleshoot those problems and prevent them from escalating. Hopefully, the tips in this article will help you fix them once and for all.
Troubleshooting New Holland Baler Knotter
Generally, troubleshooting the New Holland baler knotters involves replacing worn components or making some adjustments. A simple adjustment to the twine fingers can help. A new set of springs can make all the difference in the world. You can also try replacing a bad-quality twine.
If you are wondering how to troubleshoot the New Holland baler knotter, you have come to the right place. This article will walk you through how to troubleshoot the knotter. After determining the exact cause of the problem, follow the instructions below to troubleshoot a New Holland baler knotter.
1. Checking Twine Pullout Force
To troubleshoot a New Holland baler knotter, first, you need to determine the twine pullout force. This is the force needed to yank a single twine out of the twine box. A fish scale is a handy tool for measuring the pullout force.
If the pullout force is too low, it will likely result in the needle draw pulling out of the knot. If you notice the twine pullout force is too high or too low, you may need to adjust the tension. You can consult the manual on how to make these adjustments.
2. Checking Twine Disk Hold Force
Troubleshooting a New Holland baler knotter is easy when you know how to check the holding force of the twine disk. First, check the bolt holding the twine disk. Is it loose or tight? If the tension is low, the twine will not knot properly.
The twine holding force of a baler knotter can be adjusted by loosening or tightening a bolt that holds the bottom front of the knotter to a heavy plate.
If the holding force of the twine is too loose, the baler will have trouble holding the twine and will not perform properly. A bolt can be used to tighten the holding force of the twine disk on baler knotters.
The proper twine tension is essential for a quality bale. Ensure the bale knotter is properly lubricated. A tight bale is more stable than a loose one. Check the twine tension and adjust it if necessary.
Twine tension is measured by the amount of twist and conformity of the twine. All components of a baler must work properly to produce quality bales. Lubrication is also important because you’ll experience costly downtime without it.
3. Twine Quality
The twine used in bale knotting should be of high quality. Twine with poor quality will not knot properly, degrade quickly and not meet the quality specifications for baling twine.
Using a bale knotter properly is essential to purchasing high-quality twine. The thickness and width of the twine are also important factors in knot formation.
4. Check Springs
Before tackling any repair job, you should check the baler’s springs to ensure they’re not acting up. The springs in your knotter will break down over time and need to be replaced if they’re acting up.
The system won’t work correctly if the springs are loose or broken. If you have any doubts, you should visit a New Holland baler repair shop and ask them to replace the springs.
5. Adjusting Twine Fingers
Troubleshooting a New Holland Baler Knotter is a simple task if you understand its working principles. The twine fingers are held in place by “springs” mounted on the back of the knotter. In case of broken springs, a new one must be installed.
Twine fingers play a key role in the operation of a baler knotter. If the twine is not of good quality, it can cause many problems. Once you have determined the correct tension, you can adjust the twine fingers.
The twine will whip out of the knot if too loose or too tight. To make the knotter work properly, it must be adjusted to the proper size.
In Case You Still Haven’t Found the Solution:
If you have a New Holland baler and you’re experiencing troubleshooting issues, it’s a good idea to consult your operator’s manual. In addition, if you have a question regarding the knotter, consider posting a thread on the New Holland forums.
You’ll find other users asking the same questions and receive helpful responses from other people who have used a New Holland baler.
Summing up:
If you’re experiencing difficulty with the knotter on your New Holland baler, you’ve come to the right place. If your New Holland baler knotter has stopped working, you might wonder how to troubleshoot it.
The steps mentioned above will show you how to troubleshoot this piece of machinery. By following these simple steps, you’ll be able to fix baler knotter problems.